Archive for May, 2011

A Different Way to Zone Your Heating

Monday, May 30th, 2011

One of the most frustrating things about traditional heating is that you must pay for the entire home to be heated. You flip on the thermostat and you get the same temperature for every room. Vent covers can reduce how much heat gets to each room, but if you want one room to be cooler than another, how do you do it without installing an expensive zone control system?

Vent Levers for Adjustable Air Flow

The easiest way to control the flow of air in your heating system is to use a vent lever adjustable air flow system that allows you to actually control where the air goes. These systems are installed directly on your furnace’s air handler. Each vent lever can be attached to a specific thermostat in your house or the vent levers can be opened and closed manually from the basement. When one of the thermostats is turned off, a vent lever will close off air flow to that particular room and stop any heat from being distributed there.

The system itself is not as easy to use as a zone control system but because the technology is simple and it takes only a few seconds to the turn the vent levers, it’s a viable and effective method to control your heating if you cannot afford zone control. If you’re not sure whether this is a good solution for your particular furnace, an HVAC contractor can help.

How to Get Vent Levers Installed in Your Home

If this sounds like a good solution for you, take some time and contact your local HVAC service provider to learn more about what it takes to have vent levers installed. For some systems it is relatively easy to add them to an existing air handler. In older systems or in the case of a boiler, you may need to install more specific types of handlers to control the flow of heating to each room in your home. A professional can give you a better idea of what your home needs and how it can best be setup.

What’s the Difference Between a Furnace and a Boiler?

Friday, May 27th, 2011

When it comes time to choose a new heating system for your home, there is a good chance your choices are limited. Most homes already have either forced air or radiant heat equipment installed so choosing something different would be costly and unnecessary. But, if you have a choice or are moving into a new home, here are some things to consider regarding the difference between furnaces and boilers.

What a Furnace Does

A furnace uses a fuel like gas, oil or electricity to heat a series of coils in the device. The furnace then uses a blower to push air across the heated coil and into an air handler where it can be distributed throughout your home. This is called a forced air system and requires a combination of ducts and filters to keep air moving smoothly and cleanly throughout your home.

If you have access to gas, a gas furnace with an AFUE of 90% or higher is one of the most efficient and cost effective ways to heat your home. These furnaces can also last upwards of 20-25 years with proper maintenance.

What a Boiler Does

A boiler is different in that it uses water as the heat carrying medium, not air. Boilers still need gas, oil or electricity to heat up the water in the system, though they often use less of it than a traditional furnace – depending on the age of the furnace and the boiler. After water is heated in the boiler, your radiant heating system carries the water to baseboard heaters or radiators throughout your home. This form of heat is preferred by many because it doesn’t require ductwork (which requires extra maintenance) or extra air filtering and it is more humidity friendly in a large home.

In terms of efficiency, both boilers and furnaces are efficient if you’re buying a new model. Capacity is also evenly matched. Boilers take the edge in comfort level and if you have the budget, you can install radiant floor heating which allows you to pipe hot water directly into bathroom floors or your living space so that you never again need to walk on cold floors. Another benefit of radiant heating is that the system will hold heat much longer and then release it over time instead of turning on and off a lot as a furnace tends to do.

Check Out Our Blog for the Latest in HVAC Technology

Friday, May 20th, 2011

Be sure to bookmark the Clean Air Act blog for updates on the latest advances in Plumbing and HVAC technology.

We’ll feature money saving promotions here as well.

Call Clean Air Act for all your air conditioning, heating, and indoor air quality needs.

Welcome to Our New Website

Friday, May 20th, 2011

iMarket Solutions has launched Clean Air Act’s new custom website. To learn more about how iMarket Solutions can expand your presence on the web visit: www.imarketsolutions.com